search
  • NanoKom 3e/1s Mast Amplifier (561501) and PicoKom 1e/1s Power (5796)

NanoKom 3e/1s Mast Amplifier (561501) and PicoKom 1e/1s Power (5796)

Kit Amplifier Televes 561501. 4 inputs: BIII, UHF (TV Antenna) and FI (Satellite). With fast connections EasyF (No connectors needed) + Televes 5796 Power Supply.

This product is replaced by the NanoKom 3e/1s Mast Amplifier 561521+PicoKom 1e/1s 12V-220mA Power Supply 5796 LTE700 Televes

star star star star star
Reference televes-438840
Brand Televes
Quantity

Free shipping

Televes 561501 Amplifier Kit + Televes 5796 Power Supply

Amplifier

Masthead amplifier for the amplification and combination of terrestrial television and satellite signals coming from several antennas.
Equipped with 3 inputs: the BIII/UHF input signal is amplified, whereas the FM and SAT signals are only combined.
Allows DC pass towards the satellite input to power the LNB.

Highlights

  • Equipped with USOS (User Selectable Output Signal) technology: the installer selects the desired output level, which remains stable. The device automatically adjusts gain according to the input signal variation.
  • Separate amplification and very low noise figure, thus respecting signal quality
  • Ultra-small ergonomic design
  • EasyF connection system
  • Can be powered in the 12 V-to-24 V range
  • Fully automated manufacturing, subject to the most stringent quality controls
  • High-screening Zamak chassis

Features

  • LTE/4G filter to remove mobile phone interference
  • ON/OFF switch to allow DC pass towards the UHF input for the powering of a BOSS system
  • Easy mounting. Equipped with a plastic tie for mast mounting
  • Resistant ABS-plastic orange case for outdoor installation

 

EasyF connection system: simplicity and savings

EasyF is an innovative connection concept where the inner conductor of the coaxial cable is directly inserted in the device, thus improving connection reliability. Thanks to the absence of F connectors, the chassis can be reduced and the connection of two cables secured with a a single screw.

  • Real time savings: speeding the installation is possible without the need for coaxial cable termination. Furthermore, there is no need for screwing the connectors on the device, which is sometimes difficult when there is little room
  • Connection reliability: the clamp holding the cables prevents the coaxial cable to come off
  • Cost savings: no additional connectors are required (neither F nor IEC)
  • Space optimization: inputs and outputs are always on the same side of the device to prevent coaxial cables from bending, and to make working inside cabinets and register boxes easier
  • Very easy three-step mounting: only screwing and unscrewing the covers is required to connect both cables:

1. Unscrew the device's cover to access the connection

2. Insert the previously stripped coaxial cables

3. Close the cover and screw to ensure connection

Learn more about EasyF system reliability

With EasyF, the connection between the coaxial cable and the device is carried out using an automated system for contact insertion of the inner conductor, without any soldering. 

  • Always as new: the device's operating life increases when the factor of solder wearing out with time is removed
  • Failure rate reduction: usually produced as a result of cold soldering joints
  • Electromagnetic behaviour optimization: for high frequencies
  • Our commitment with environment is reinforced: pollution caused by the welding process is eliminated and production power consumption is reduced

Specifications

Bands UHF + BIII BI + FM SAT
Frequency margin MHz 470-790 174-254 47-108 950-2150
Gain dB 27 20 -2 -2.5
Gain adjustment range dB AUTO
0 ... 15
AUTO
0 ... 15
- -
Max.output level dBμV DIN 45004B 107 105 - -
EN 50083 114 112 - -
10 CH DVB-T 94 - - -
2 CH DVB-T - 90 - -
Output level regulation margin dB (Manual) 0...12 (Manual) 0...12 - -
Noise figure dB 2.5 3.5 - -
Power supply V /mA 12 ... 24 / 45
Max current through inputs OFF mA 0
ON 40 - -
DC OUT -> DC SAT - - - 300
Protection Level IP 23
Temperature operat. limits ºC -5 ... +45

Power Supply

Domestic 12 V-power supply (220 mA) that powers equipment through the input coaxial cable while allowing the transmission of the TV signal. Included in the installation to power either mast amplifiers or a BOSS system. Compatible with satellite combination amplifiers (IFmix), since the equipment detects the presence of the LNB management signal on the output (voltage and tone) generated by a receiver, allowing it to reach the input.

Highlights

  • High-performance switched-mode power supply: saves up to 40% power consumption
  • Very low power consumption
  • Pleasing design and ultra-small size: can be installed in 100 mm x 100 mm connection boxes
  • EasyF connection system
  • Fully automated manufacturing, subject to the most stringent quality controls

Features

  • Can be wall-mounted using screws
  • The IFmix functionality allows it to work in an satellite installation respecting the LNB supply

 

EasyF connection system: simplicity and savings

EasyF is an innovative connection concept where the inner conductor of the coaxial cable is directly inserted in the device, thus improving connection reliability. Thanks to the absence of F connectors, the chassis can be reduced and the connection of two cables secured with a a single screw.

  • Real time savings: speeding the installation is possible without the need for coaxial cable termination. Furthermore, there is no need for screwing the connectors on the device, which is sometimes difficult when there is little room
  • Connection reliability: the clamp holding the cables prevents the coaxial cable to come off
  • Cost savings: no additional connectors are required (neither F nor IEC)
  • Space optimization: inputs and outputs are always on the same side of the device to prevent coaxial cables from bending, and to make working inside cabinets and register boxes easier
  • Very easy three-step mounting: only screwing and unscrewing the covers is required to connect both cables:

1. Unscrew the device's cover to access the connection

2. Insert the previously stripped coaxial cables

3. Close the cover and screw to ensure connection

Learn more about EasyF system reliability

With EasyF, the connection between the coaxial cable and the device is carried out using an automated system for contact insertion of the inner conductor, without any soldering. 

  • Always as new: the device's operating life increases when the factor of solder wearing out with time is removed
  • Failure rate reduction: usually produced as a result of cold soldering joints
  • Electromagnetic behaviour optimization: for high frequencies
  • Our commitment with environment is reinforced: pollution caused by the welding process is eliminated and production power consumption is reduced

Specifications

Outputs   1
Frequency margin MHz 5 ... 2400
Insertion loss MIN dB -4
MAX -6
Power supply Vdc 12
Max. current inputs mA 220
Mains voltage/frequency V~/Hz 196 ··· 264 / 50 - 60
Total AC consumption W 3.7
Protection Level IP 20
Temperature operat. limits ºC -5 ... +45
 

Summary

0

star_border star_border star_border star_border star_border

0 Reviews

Only users who already bought the product can add review.

Write your review

monetization_on Write your review and get voucher for discount 3%
*valid for 60 days

No customer reviews for the moment.