• -35%

NanoKom mast amplifier kit and PicoKom power supply Ref. 561721 + Ref. 5795 Televes

Mast Amplifier Kit for DTT composed of amplifier 561721 and power supply 5795. NanoKom mast amplifier, 3 inputs: UHF-UHF-VHFmix. PicoKom power supply, 24V - 130mA, 2 outputs

star star star star star
€53.91 €82.95 Save 35%
Tax included
Reference televes-568010
Brand Televes
Available in 24/48h

Free shipping

NanoKom mast amplifier kit and PicoKom power supply Ref. 561721 + Ref. 5795 Televes

€53.91 €82.95 Save 35%

You might also like

Kit composed of:

Ref. 561721: NanoKom mast amplifier, 3 inputs: UHF-UHF-VHFmix

Mast installation amplifier to amplify and mix terrestrial television signals from various antennas.

It consists of 3 inputs: the signal is amplified in the two UHF inputs, while the VHF signal is only mixed. The amplifier is powered through the output coaxial cable.

RED Compliant.

Ref. 5795: PicoKom power supply, 24V - 130mA, 2 outputs

24V (130mA) source that sends power through the input coaxial cable, allowing the TV signal to pass through. It is inserted in the installation to feed mast amplifiers or a BOSS system. In addition, it incorporates a distributor to generate two outputs.

Stands out for

  • Separate amplification and very low noise figure, thus respecting the quality of the signal
  • Ultra slim ergonomic design
  • EasyF connection system
  • They can be powered from 12 to 24V
  • Fully automated manufacturing and subject to rigorous quality controls
  • High armor chassis, made of Zamak

Main features

  • LTE700/5G filter to eliminate telephone interference
  • ON/OFF switch to allow DC to pass through to the UHF input, to power a BOSS system
  • Simple assembly. Flange for attachment to the mast included
  • Strong orange ABS plastic box for outdoor installation

EasyF connection system: simplicity and savings

The EasyF is an innovative connection concept of the internal conductor of the coaxial cable (live), which is inserted directly into the device, increasing the reliability of the connection. In addition, thanks to the absence of "F" connectors, it is possible to reduce the chassis and secure the connection of two cables with a single screw.

Real time savings: it is possible to speed up the installation, since it is not necessary to carry out the connectorization of the coaxial cables. In addition, the threading process of the connectors on the device, which is sometimes complicated when the space is not enough, is avoided.

Reliability of connection: the clamp that holds the cables prevents the coaxial from coming loose

Cost savings: no additional connector (neither "F" nor "IEC") needed

Space optimization: inputs and outputs are always located on the same side of the device, avoiding bending coaxial cables and facilitating work inside cabinets and registers

Very simple assembly in three steps: only screwing and unscrewing of the covers is required to connect two cables:

1. Unscrew the cover of the device to access the connection

2. Insert the previously stripped coaxial cables

3. Close the lid and screw to secure the connection

Find out more about the reliability of the EasyF system

With EasyF, the connection of the coaxial cable to the device is carried out by means of an automated system for inserting the live (internal conductor) by contact, without requiring soldering.

  • Like the first day: the lifetime of the device is increased by eliminating the possible deterioration of the welds over time
  • Reduced failure rate: generally caused by cold welds
  • Optimization of electromagnetic behaviour: at high frequencies
  • Reinforcement of our commitment to the environment: pollution caused by the welding process is eliminated and electricity consumption in production is reduced



star_border star_border star_border star_border star_border

0 Reviews

Only users who already bought the product can add review.

Write your review

monetization_on Write your review and get voucher for discount 3%
*valid for 60 days

No customer reviews for the moment.